Loading...
2 results
Search Results
Now showing 1 - 2 of 2
- A new application of solvent extraction to separate copper from extreme acid mine drainage producing solutions for electrochemical and biological recovery processesPublication . Nobahar, Amir; Melka, Alemu Bejiga; Pusta, Alexandra; Lourenço, João P.; Carlier, Jorge; Costa, Maria ClaraOver the last decade, AMD waters have gained more attention as a potential source of metals due to the emerging need to recover or recycle metals from secondary resources. Metals recovery supports sustainability and the development of a circular economy with benefits for resource conservation and the environment. In this study, five extractants (Acorga M5640, LIX 54, LIX 622, LIX 622 N, and LIX 864) diluted (15% (v/v)) in Shell GTL with 2.5% (v/v) octanol were compared and evaluated for Cu recovery from an extreme AMD sample (5.3 +/- 0.3 g/L Cu) collected at the inactive Sao Domingos Mine in the Iberian Pyrite Belt of Portugal. Of the five extractants, Acorga M5640 showed the best selective efficiency. Further tests showed that 30% (v/v) of this extractant was able to selectively extract approximate to 96.0% of the Cu from the AMD in one extraction step and all of the remaining Cu (to below detection) in three steps. Among the different stripping agents tested, 2 M sulfuric acid was the most efficient, with approximate to 99% of the Cu stripped, and the recyclability of the organic phase was confirmed in five successive cycles of extraction and stripping. Furthermore, contact time tests revealed that the extraction kinetics allows the transfer of approximate to 97% of the Cu in 15 min, and aqueous to organic phase ratios tests demonstrated a maximum loading capacity of approximate to 16 g/L Cu in the organic phase. Raising the concentration of Cu in the stripping solution (2 M sulfuric acid) to approximate to 46 g/L through successive striping steps showed the potential to recover elemental Cu using traditional electrowinning. Finally, a biological approach for Cu recovery from the stripping solution was evaluated by adding the supernatant of a sulfate-reducing bacteria culture to make different molar ratios of biogenic sulfide to copper; ratios over 1.75 resulted in precipitation of more than 95% of the Cu as covellite nanoparticles.
- Zinc recovery from an extreme copper-free acid mine drainage: studying the prior separation of ferric iron by solvent extraction using AliCy and/or alkalinizationPublication . Nobahar, Amir; Melka, Alemu Bejiga; Marín-Beltrán, Isabel; Neves, Luiz; Costa, Maria Clara; Dias Carlier, JorgeZn recovery attempts from a copper-free extreme Acid Mine Drainage with similar to 53 g/L Fe and similar to 2 g/L Zn revealed Fe co-extraction in solvent extraction with 0.9 M D2EHPA or a mixture of 0.72 M D2EHPA and 0.18 M Cyanex 272, and simultaneous precipitation of Fe during zinc sulfide recovery through biogenic sulfide addition. Therefore, alkalinization, solvent extraction with the self-prepared ionic liquid AliCy diluted in kerosene, and combinations of both these methods were studied for the separation of ferric iron (Fe3+) from such water, prior to Zn recovery. The most efficient strategy tested was a solvent extraction cycle with AliCy followed by alkalinization of its aqueous raffinate to pH 3.25 or 3.5. As a result of this approach, similar to 92% of Fe3+ is separated by SX and the remaining is removed by precipitation, with just similar to 12% or similar to 17% Zn losses, respectively. Afterwards, the highest Zn recovery from water resulting from such combination of processes was achieved by precipitation through addition of biogenic sulfide at pH = 3.5. The obtained precipitates are nanoparticles of Wurzite and Sphalerite (ZnS) of sizes between 2 to 22 nm agglomerated into larger structures. This work shows for the first time the potential of AliCy to separate Fe3+ from acidic multimetallic solutions, a known contaminant of several metal recovery processes.